您好!欢迎光临 EDT Diecasting Technology (Suzhou) Co., LTD 网站!

Zinc vs Aluminium Die Casting: How to Choose

Release time:2026-11-17view count:6

“Zinc or aluminium?” is the question we hear most often at the quoting stage, and the one most often answered badly. Two extremes are common: zinc is expensive, so use aluminium for everything; or zinc holds tighter tolerances, so use zinc for everything. Both end up costing more.

This guide breaks the decision into six criteria and gives an order to work through them — what to look at first, and what to talk about last.

1. Material price is not part cost

Zinc ingot typically costs more than twice as much as aluminium per kilogram. That is where the “zinc is expensive” impression comes from — but it ignores density.

  • Zinc alloy density is about 6.6 g/cm³; aluminium about 2.7 g/cm³

  • For the same part volume, a zinc part weighs roughly 2.4 times as much

  • So the price gap per kilogram is amplified by weight, not reduced

The real difference lies elsewhere. Zinc melts at around 385 °C, aluminium at around 600 °C. Lower melting point means less melting energy, and zinc can run on hot-chamber machines — melting pot and injection integrated, shorter cycle, higher output. Zinc is also gentler on tooling, so die life is significantly longer.

The practical result: for small, precise and cosmetic parts, zinc often wins on total cost. For large structural and load-bearing parts, aluminium wins. Comparing material price alone usually leads to the wrong answer.

2. Six criteria to work through

CriterionZinc alloyAluminium alloy
Material and part costHigher unit price, higher density; often cheaper for small partsLower unit price; better for large parts
Dimensional accuracyLow shrinkage, tighter tolerances and thinner wallsHigher shrinkage, thin walls harder to control
Strength and heatModerate strength; not ideal for sustained heatHigh strength and heat resistance
Surface finishingBest for plating (Ni/Cr) and polishingAnodising, powder coating, passivation
CorrosionStable indoorsNeeds coating or anodising outdoors
Volume and toolingHot chamber, short cycle, long die lifeCold chamber, longer cycle, higher tooling cost

3. Accuracy: where zinc wins

Zinc shrinks about 0.4–0.6% and flows well, so it fills thin sections more reliably. Three practical consequences:

  • Very thin walls (thin housings, decorative plates) are easier to hold in zinc

  • Small precision parts that must be close to final size as-cast favour zinc

  • Parts that will be plated or polished benefit from a zinc substrate

Aluminium shrinks about 0.6–1.0% with a wider solidification range, so thin walls and fine features are harder to keep consistent. Precision aluminium parts often need CNC afterwards — which adds cost.

4. Strength and temperature: where aluminium wins

Aluminium has a much better strength-to-weight ratio and handles heat better, so structural, load-bearing and heat-adjacent parts almost always use aluminium.

  • Automotive safety parts (steering, actuators, chassis supports) — strength and fatigue life

  • Thermal parts — aluminium conducts heat far better than zinc

  • Outdoor structural parts — anodising provides durable protection

Zinc loses strength faster under sustained heat, so it is not the right choice near engines or lamp heat sources.

5. Surface finish often decides the material

FinishZincAluminium
Plating (Ni/Cr)First choice, excellent adhesion and brightnessNeeds special pre-treatment, higher cost
PolishingExcellent, ideal for decorative partsSofter, scratches easily
AnodisingNot applicableFirst choice, colour and hard anodising
Powder coatingPossibleCommon

Appliance knobs, decorative rings and hinges — parts that are seen and must look bright — are almost always zinc. Parts needing matte, coloured or wear-resistant surfaces are aluminium with anodising.

6. Typical applications

ApplicationUsual choiceTypical parts
Appliance drive and trimZincDoor shafts, latches, selector rings
Automotive structure and safetyAluminiumSteering components, actuator housings, sunroof parts
Electronics thermal and structureAluminiumCPO heat sink brackets, HDD brackets, motor brackets
Energy and fluid controlMostly aluminiumGas regulators, gas valve bodies
Enclosures and industrial hardwareZincCabinet handles

On our own lines: household appliance castings are mostly zinc, automotive castings mostly aluminium, alongside electronics castings and energy management castings.

Zinc examples: door shaft, washing machine selector ring, cabinet handle — small, light, appearance-critical.

For thin-wall capability in aluminium, actuator housing is a good example: wall thickness control is the hard part.

7. When both materials would work

Many parts can be made in either. Work through these four questions in order:

  • Annual volume? At low volumes tooling amortisation dominates, and zinc's hot-chamber process and long die life help more

  • How tight is the tolerance? If it must be near-final as-cast, lean zinc

  • Any cosmetic requirement? High-bright plating points to zinc; colour and matte point to aluminium

  • What is the service environment? Heat, outdoors or load-bearing favour aluminium

If all four point the same way, the decision is clear. If they conflict — high precision plus high strength, for example — the usual solution is an aluminium body with machining allowance on the critical interfaces.

8. The cost item people forget

Always include downstream operations. Plating and polishing for zinc, anodising and powder coating for aluminium differ a lot in unit cost and yield. And when an aluminium part needs machining at several locations, the machining hours usually cost more than the material difference.

In short: compare the complete cost from blank to finished part, not the material price per kilogram.

We run both zinc and aluminium lines and can recommend a material and give a cost estimate before tooling is cut. If you are stuck on a drawing, send the critical dimensions and service conditions and we will give you a comparison.

Message
Hotline

Hotline

0512-67371602

WeChat
EDT Diecasting Technology (Suzhou) Co., LTD
Top